Kitchenaid microwave error codes

Kitchenaid microwave error code f7

Kitchenaid microwave error code f7

This error code signifies a problem in the inverter or magnetron tube, or both. The inverter board can be destroyed by the magnetron tube. This appears to be a design issue. If you have this problem, you are going to have to replace either the magnetron tube or inverter.

Kitchenaid microwave open close door error

Kitchenaid microwave open close door error

If you see the error code, and the door is closed, thre must bee open circuit in the door interlock switch circuit. Switches are found inside the cooking cabinet: they are designed t catch the door once it is closed. Most likely, it is a door interlock switch problem, which requires repair or replacement of these switches.

Maybe you will need to just unplug your microwave for 1-2 minutes or so and then plug it back it. If it does not work, you are going to have to disassemble the element and check all its tiny parts. It is advisable to use professional help.

Kitchenaid microwave f2 error code

Kitchenaid microwave f2 error code

This error code indicates a keyboard failure. Reset your microwave and see if the code reappears. If it does, check and repair/replace the touch panel. If this does not work either, you will need to check, repair or replace the control board. If you are not experienced enough, use professional help.

Other error codes

Kitchenaid microwave error codes
The table lists the main errors with a description of the fault, which triggered the output of an error code on the display. The solution to the problem is indicated in the table opposite each error.

What is the Error CodeCausePossible Solutions
DOOR or OPEN and CLOSE DOOR in displayIf a message about the door appears in the display, the door has been closed for 5 minutes or more without the microwave oven being started.This occurs to avoid unintended starting of the microwave oven.
Open and close the door, then start the cycle.
Is the door fully closed?
- Remove all packing material from the Microwave.
- Be sure no packing material is blocking the door lock system.
- Close the door firmly.
- Check that the cooking rack (if equipped) is not out of position and not allowing the door to close.
Flashing or PFThere has been a power failure or the clock time has been turned off. When power is first supplied to the microwave oven, a colon ( : ) will blink in the display.Touch the "Cancel/Off" or "Cancel" key (depending upon model) to stop the blinking.
Has a power failure occurred?
- If the colon " : " blinks in the display a power failure has occurred. Touch the "Cancel/Off" or "Cancel" key, and reset the clock as needed. If an invalid value has been entered, the invalid entry tones will sound and the input prompt will reappear in the display. Retry your entry.
- When the microwave oven is in use, the display shows cooking power, quantities, weights and/or prompts. - When the microwave oven is not in use (standby mode), the display shows the time of day or Timer countdown.
- If the ":" or PF continues to flash contact a qualified electrician.
LOC or "L" or Padlock IconThe Control Lock feature is ENABLEDDepending on model:
- Press & Hold Cancel key for 3 seconds.
- Press & Hold Start key for 5 seconds.
SE CodeThere is a problem with the Keypad (User Interface) or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave oven for one (1) minute to ensure the error code does not display again.
Verify microwave oven operation.
ЕОЗThe Keypad (User Interface) reported a problem to the control board. There may be a problem with the Keypad (User Interface) or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
Е11The Gas Sensor reported a problem to the control board. There may be a problem with the Gas Sensor or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
Е12There is a problem with the Gas Sensor or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
Е13The oven did not pre-heat correctly. There may a problem with the Appliance Control Board or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
Е21The Thermal Sensor circuit reported open to the control board. There may a problem with the Thermal Sensor, the Appliance Control Board, or the associated wiringPower unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
Е22The Thermal Sensor circuit reported a short to the control board. There may a problem with the Thermal Sensor, the Appliance Control Board, or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
Е23The oven did not reach Pre-Heat Temperature within 30 (thirty) minutes. There may a problem with the Heater, the Appliance Control Board, or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
Е61The oven sensor circuit reported an open condition to the control board. There may a problem with the Sensor, the Appliance Control Board, or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
Е62The Oven Sensor circuit reported a shorted condition to the control board. There may a problem with the Sensor, the Appliance Control Board, or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
Е63The Oven Sensor circuit reported a shorted condition to the control board. There may a problem with the Sensor, the Appliance Control Board, or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F1 E1The oven could not execute the function. There may a problem with the Relay Control Board, or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F1 E4The oven could not execute the function. There may a problem with the Appliance Control Board, or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F2The Keypad (User Interface) reported a problem to the control board. There may be a problem with the Keypad (User Interface) or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F2.H1There may be a problem with the Vent Fan and Light Switch (located on the lower left front side panel) or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F2.H2There may be a problem with the Vent Fan and Light Switch (located on the lower left front side panel) or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F2.Q1There may be a problem with the User Interface (Touchpad) or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F2E1There may be a problem with the User Interface / Keypad or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F2H1There may be a problem with the Vent Fan and Light Switch or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F2H2There may be a problem with the Vent Fan and Light Switch or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F3.H1There may be a problem with the Humidity Sensor or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F3.T1There may be a problem with the User Interface Thermistor or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F3.T2There may be a problem with the Convection Thermistor or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F3.T3There may be a problem with the Hood Temperature Thermistor or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F3.T4There may be a problem with the Magnetron Temperature Thermistor or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F3CThere may be a problem with the Cavity Temperature Thermistor or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F3HThere may be a problem with the Humidity Thermistor or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F4E1There may be a problem with the Cavity Temperature Thermistor or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F4E4There may be a problem with the Humidity Thermistor or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F4E9There may be a problem with the Smart Pop Control or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F6The oven could not execute the function. There may a problem with the Relay Control Board, or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F6E0The oven could not execute the function. There may a problem with the Appliance Control Board, or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F7The oven could not execute the function. There may a problem with the Appliance Control Board, or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F8E5The oven could not execute the function. There may a problem with the Exhaust Air Temperature Sensor, or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F9The oven could not execute the function. There may a problem with the Appliance Control Board, the Relay Control Board, or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F9.QThe oven could not execute the function. There may a problem with the User Interface (Touch Pad) or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.
F9.Q1The oven could not execute the function. There may a problem with the User Interface (Touch Pad) or the associated wiring.Power unit down by turning off the circuit breaker(s) for one (1) minute.
Power unit up by turning on the circuit breaker(s).
Monitor the microwave for one (1) minute to ensure the error code does not display again.
Verify microwave operation.